Images are representations only.
Meter, Turbine, 4 Inch, Guardsman™ LJ-H, Model K2EE and LJ-V Model K2PE Series - Spare Parts
Description
The Smith Meter® Guardsman™ Series Turbine Meter is a bladed, rotor-type meter which utilizes an upstream, cantilevered stator to support the tungsten carbide, bearing-mounted rotor.
It is intended for a wide range of petroleum, petrochemical, and chemical custody transfer measurement applications, such as small product pipelines ranging from Natural Gas Liquids (NGL) to light fuel oils.
Smith Meter Guardsman Series L Models are rimless-type rotor turbine meters that use an upstream stator to support the rotor.
They are intended for use at loading racks to provide the highly accurate measurement required for custody transfer of petroleum liquids.
Note: Different features and requirements are available based on where a unit is manufactured.
Throughout this document, manufacturing locations are denoted in parentheses after a feature.
You must place your order with the noted location to receive a unit with the specific feature.
Features- 1.5" to 4" Guardsman™ (G) Series
- Stainless Steel measuring chamber and internals
- Locking stator prevents wear and improves performance
- Tungsten carbide bearings system provides longlife on low lubricating fluids
- Hydrodynamic thrust balance to minimize friction and wear on thrust bearings which allows for long service life and high accuracy
- 125-250 AARH flange face finish
- 1" to 4" Guardsman™ Series Loading Rack (L) Models Turbine Meters
- Stainless-steel measuring chamber and internals
- Locking stator prevents wear and improves performance
- Stainless Steel ball bearings (LB models) and tungsten carbide journal bearings (LJ and LSJ models) provide long life on low lubricating fluids
- Integral-strate-plate flow conditioner (LSJ models)
- Horizontal or vertical installation
- Turbine Meter Diagnostics when used with AccuLoad III
Inventory
Displaying prices & availability for Ohio, United States in USD. Change location.
Models matching criteria: 43
Nut, #10-32 - Item 15
In Stock
$1.00 USD
Pin, Dowel, ⅛ x ⅜" - Item 23
In Stock
$2.00 USD
O-Ring - Item 16
In Stock
$3.00 USD
Screw, Set, #6-32 X ¼" - Item 11
In Stock
$5.00 USD
Clip, Retaining - Item 6
In Stock
$6.00 USD
Washer, Inverted (ATEX version only) - Item 28
In Stock
$13.00 USD
Wire, Ground (UL/CSA version only) - Item 29
In Stock
$16.00 USD
Label: UL/CSA Approvals - Item 12
In Stock
$23.00 USD
Connector, (1-6) - Item 2
In Stock
$27.00 USD
Connector, (6-10) - Item 3
In Stock
$27.00 USD
Screw, Set, #10-32 - Item 24 view more
- Note 3: Apply a small amount of Loctite (Part No. 643917-401) to set screw before installing
In Stock
$27.00 USD
Stud (ATEX version only) - Item 26
In Stock
$72.00 USD
Cover, Conduit Box: UL/CSA Approvals - Item 10
In Stock
$110.00 USD
Cone, Upstream: Horizontal - Item 9
In Stock
$114.00 USD
In Stock
$116.00 USD
Cover, Conduit Box: ATEX – Manufactured in USA - Item 10
In Stock
$141.00 USD
Cone, Downstream: Horizontal - Item 8
In Stock
$173.00 USD
Cone, Downstream: Vertical - Item 8
In Stock
$255.00 USD
Cone, Upstream: Vertical - Item 9
In Stock
$255.00 USD
In Stock
$275.00 USD
Box, Conduit - Item 5
In Stock
$294.00 USD
Bearing, Journal: Horizontal - Item 4
In Stock
$316.00 USD
Coil, Pickup: Mating Connector with Leads (High Temp Version) - Item 7 view more
- Recommended Stock
In Stock
$320.00 USD
Bearing, Journal: Vertical - Item 4
In Stock
$349.00 USD
In Stock
$444.00 USD
Rotor Bearing - Item 19
In Stock
$448.00 USD
Coil, Pickup: -100°F to 400°F (High Temperature Version) - Item 7 view more
- Recommended Stock
In Stock
$746.00 USD
Stator Assembly, Locking - Item 22
In Stock
$1,420.00 USD
Rotor Assembly: Current Design, 430 Stainless Steel – Horiz & Vert - Item 18 view more
- Note 2: Due to a change in the design of this meter in December of 1987, it is necessary to determine whether your meter is of current or previous design. Standard serial numbers up to and including 5216, and special serial numbers up to and including 200822 are considered previous design. Numbers higher than those are current design. These numbers can be found on the nameplate and on the stator.
In Stock
$3,275.00 USD
Washer, ¼" Lock (ATEX version only) - Item 27
In Stock
Nut, Hex, ¼"-20, UNC-2B (ATEX version only) - Item 25
In Stock
Screw, #10-32 x ¼" - Item 20
In Stock
Gasket, Cover - Item 13
In Stock
Cover, Conduit Box: ATEX – Manufactured in Germany - Item 10
In Stock
Label: ATEX – Manufactured in USA - Item 12
In Stock
Label: ATEX – Manufactured in Germany - Item 12
In Stock
In Stock
Rotor Assembly: Previous Design, 430 Stainless Steel - Item 18 view more
- Note 2: Due to a change in the design of this meter in December of 1987, it is necessary to determine whether your meter is of current or previous design. Standard serial numbers up to and including 5216, and special serial numbers up to and including 200822 are considered previous design. Numbers higher than those are current design. These numbers can be found on the nameplate and on the stator.
In Stock
Internal Parts Kit - Unidirectional - 430 Stainless Steel Rotor - Horizontal view more
- Note 4: If meter is used with a Strate Plate, when ordering Internal Parts Kit, use the prefix of ‘FC’ to the part number for the Internal Parts Kit required
In Stock
Internal Parts Kit - Unidirectional - 430 Stainless Steel Rotor - Vertical view more
- Note 4: If meter is used with a Strate Plate, when ordering Internal Parts Kit, use the prefix of ‘FC’ to the part number for the Internal Parts Kit required
In Stock
Specifications
Specifications
Brand
Repeatability
- ± 0.02 % over the normal flow range
End Connections
- Class 150 and 300 American Society of Mechanical Engineers (ASME) B16.5, 125-250 Arithmetic Average Roughness Height (AARH) finish raised-face (RF) flanges
- Class 150, 300, 600, 900 ASME B16.5, 125-250 AARH finish raised face (RF) flanges
- PN 16, 25 and 40 DIN 2526 Form C flange
- PN 63 and 100 DIN 2526 Form E flanges
