Images are representations only.
Meter, Turbine, 1½ Inch, Guardsman™ G, Model K2BA and GLJ-H Model K2EA Series - Spare Parts
Description
The Smith Meter® Guardsman™ Series Turbine Meter is a bladed, rotor-type meter which utilizes an upstream, cantilevered stator to support the tungsten carbide, bearing-mounted rotor.
It is intended for a wide range of petroleum, petrochemical, and chemical custody transfer measurement applications, such as small product pipelines ranging from Natural Gas Liquids (NGL) to light fuel oils.
Smith Meter Guardsman Series L Models are rimless-type rotor turbine meters that use an upstream stator to support the rotor.
They are intended for use at loading racks to provide the highly accurate measurement required for custody transfer of petroleum liquids.
Note: Different features and requirements are available based on where a unit is manufactured.
Throughout this document, manufacturing locations are denoted in parentheses after a feature.
You must place your order with the noted location to receive a unit with the specific feature.
Features- 1.5" to 4" Guardsman™ (G) Series
- Stainless Steel measuring chamber and internals
- Locking stator prevents wear and improves performance
- Tungsten carbide bearings system provides longlife on low lubricating fluids
- Hydrodynamic thrust balance to minimize friction and wear on thrust bearings which allows for long service life and high accuracy
- 125-250 AARH flange face finish
- 1" to 4" Guardsman™ Series Loading Rack (L) Models Turbine Meters
- Stainless-steel measuring chamber and internals
- Locking stator prevents wear and improves performance
- Stainless Steel ball bearings (LB models) and tungsten carbide journal bearings (LJ and LSJ models) provide long life on low lubricating fluids
- Integral-strate-plate flow conditioner (LSJ models)
- Horizontal or vertical installation
- Turbine Meter Diagnostics when used with AccuLoad III
Inventory
Displaying prices & availability for Ohio, United States in USD. Change location.
Models matching criteria: 44
Nut, Hex, #2-56 - Item 15 view more
- Recommended Stock
- Thread-locking adhesive (Part No. 642917401) should be used to lock nut on stator shaft, #27, and to secure set screw #11
In Stock
$1.00 USD
O-Ring, (Carbon Steel Housing only) - Item 17
In Stock
$3.00 USD
Screw, Set, #8-32 x 3/16" - Item 27 view more
- Thread-locking adhesive (Part No. 642917401) should be used to lock nut on stator shaft, #27, and to secure set screw #11
In Stock
$3.00 USD
Coil, Pickup: -100°F to 225°F - Item 7
In Stock
$4.00 USD
Screw, Set, #6-32 x ¼" - Item 11 view more
- Thread-locking adhesive (Part No. 642917401) should be used to lock nut on stator shaft, #27, and to secure set screw #11
In Stock
$5.00 USD
Clip, Retaining - Item 6
In Stock
$6.00 USD
Pin, Dowel - Item 26
In Stock
$12.00 USD
Washer, Inverted, ATEX version only - Item 29
In Stock
$13.00 USD
In Stock
$16.00 USD
Wire, Ground, UL/CSA versions only - Item 32
In Stock
$16.00 USD
Label: UL/CSA Approvals - Item 12
In Stock
$23.00 USD
Connector, (1-5) - Item 2
In Stock
$27.00 USD
Connector, (6-10) - Item 3
In Stock
$27.00 USD
Stud, ATEX Version only - Item 28
In Stock
$72.00 USD
Cover, Conduit Box: UL/CSA Approvals - Item 10
In Stock
$110.00 USD
Cover, Conduit Box: ATEX Manufactured in U.S.A - Item 10
In Stock
$141.00 USD
Box, Conduit - Item 5
In Stock
$294.00 USD
Bearing, Platform: Smooth - Item 4
In Stock
$483.00 USD
In Stock
$483.00 USD
Rotor Assembly: Standard - Item 20 view more
Due to a change in the design of this meter in September of 1989, it is necessary to determine whether your meter is of current or previous design. Standard serial numbers up to and including 6252, and special serial numbers up to and including 200995 are considered previous design. Numbers higher than those are considered current design. Should either an upstream or downstream cone require replacement on a previous design meter, it will be necessary to replace both at the same time. Cones on current design meters can be replaced individually.
In Stock
$3,632.00 USD
Washer, Lock, ¼", ATEX version only - Item 30
In Stock
Screw, #10-32 x ¼" - Item 22
In Stock
Gasket, Conduit Box - Item 13
In Stock
Cone, Downstream: Unidirectional or Bidirectional - Item 8
In Stock
Cone, Upstream: Unidirectional or Bidirectional - Item 9
In Stock
Cover, Conduit Box: ATEX Manufactured in Germany - Item 10
In Stock
Label: ATEX Manufactured in U.S.A - Item 12
In Stock
Label: ATEX Manufactured in Germany - Item 12
In Stock
In Stock
Ring, Stator Locking (Used on 900# Flange Meters only) - Item 19
In Stock
Spacer, Stator (Used on 900# Flange Meters only) - Item 24
In Stock
Stator Assembly - Item 25
In Stock
In Stock
Washer, Lock - Item 33
In Stock
Internal Parts Kit - Unidirectional, (STD Linearity)
In Stock
Internal Parts Kit - Bidirectional, (STD Linearity)
In Stock
Internal Parts Kit - Unidirectional, (Premium Linearity)
In Stock
Internal Parts Kit - Bidirectional, (Premium Linearity)
In Stock
Coil, Pickup: -100°F to 400°F (High Temperature Version) - Item 7
In Stock
Coil, Pickup: Mating Connector with Leads (High Temperature Version) - Item 7
In Stock
Specifications
Specifications
Brand
Repeatability
- ± 0.02 % over the normal flow range
End Connections
- Class 150 and 300 American Society of Mechanical Engineers (ASME) B16.5, 125-250 Arithmetic Average Roughness Height (AARH) finish raised-face (RF) flanges
- Class 150, 300, 600, 900 ASME B16.5, 125-250 AARH finish raised face (RF) flanges
- PN 16, 25 and 40 DIN 2526 Form C flange
- PN 63 and 100 DIN 2526 Form E flanges
